# Orijinal Lastik Hakkında Bilgiler

**Orijinal Kalos’ta Tavsiye Edilen Lastik Modelleri:**

- 185/55R15 82V [2.2 Bar Hava Şişirim = 31,9083 PSI]
- 185: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)
- 185 Milimetre = 18,5 Santimetre = 0,185 Metre
- Identifies the tire section width, which is the measurement of the tire from sidewall to sidewall in millimeters. This measurement varies depending on the rim to which it is fitted.

- 55: YANAK YÜKSEKLİĞİ (LASTİĞİN TABAN GENİŞLİĞİNİN %’SEL ORANI)
- 18,5 Santimetrenin %55’i = 18,5 cm x 0,55 = 10,175 Santimetre
- Is the two-figure aspect ratio. This percentage compares the tire’s section height with the tire’s section width. For example, this aspect ratio of 55 means that the tire’s section height is 55% of the tire’s section width.

- R:
- R indicates the construction used within the tires casing. R stands for radial construction. B means belted bias and D stands for diagonal bias construction.

- 15: JANT ÇAPI (“İnç” ölçü birimi cinsinde 15 = 38,1 Santimetre)
- The last dimension listed in the size is the diameter of the wheel rim (jant çapı) , which is most often measured in inches.

- 82: LASTİK BAŞINA DÜŞEN TAŞIYIM KAPASİTESİ ( TAŞIYIM İNDEKSİ ÇİZELGESİNE GÖRE 82 = 475 KG
- The load index tells you how much weight the tire can support when properly inflated. Load indexes typically range from 70 – 126, with each numeric value corresponding to a certain carrying capacity. The higher toe tire’s load index number, the greater its load carrying capacity. The carrying capacity for each value can be found on a load index chart. On each U.S. passenger car tire, the load limit is listed in pounds. European tires have the load limit listed in kilograms and sometimes pounds.
- When it comes to Light Truck (LT) or Special Trailer (ST) tires, there are two load indexes branded (example – LT235/75R15 104/101S). In this example, the 104 corresponds to 1,984 pounds (see chart below), and the 101 corresponds to 1,819 pounds. So which number do you use? The answer is, it depends on the how the tire is being used…and it can change.
- LT tires are commonly used on trucks with dual rear wheels and are branded with two load indexes. The first number indicates load carrying capacity if the tire is installed on a truck with a single-wheel rear axle, and the second number applies when the tire is used in a dual rear application.
- TYRE LOAD INDEX (ÇİZELGE):

- V: [V = 149 MPH = Saatte 239,792 Kilometre Hızla Gidebilir]
- Speed ratings are represented by letters ranging from A to Z. Each letter coincides to the maximum speed a tire can sustain under its recommended load capacity. For instance, V is equivalent to a maximum speed of 149 mph. Even though a tire can perform at this speed General Tire does not advocate exceeding legal speed limits. It is also important to note that speed ratings only apply to tires that have not been under-inflated, overloaded, damaged, or altered.
- Rating Maximum Speed Use
- L 75 MPH Off-Road & Light Truck tires
- M 81 MPH Temporary Spare tires
- N 87 MPH
- P 93 MPH
- Q 99 MPH Winter tires (w/or w/out studs)
- R 106 MPH H.D. Light Truck tires
- S 112 MPH Family Sedans & Vans
- T 118 MPH Family Sedans & Vans
- U 124 MPH
- H 130 MPH Sport Sedans & Coupes
- V 149 MPH Sports Cars, Sport Sedans & Coupes
- Z Over 149 MPH Sports Cars

**Bu Lastik ile, Aracın Yerden Yüksekliği:**- 58,45 cm = 20,35 cm (10,175 cm x 2) + 38,1 cm

- 185: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)
- 185/60R14 82H [2.1 Bar Hava Şişirim = 30,4579 PSI]
- 185: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)
- 185 Milimetre = 18,5 Santimetre = 0,185 Metre
- Identifies the tire section width, which is the measurement of the tire from sidewall to sidewall in millimeters. This measurement varies depending on the rim to which it is fitted.

- 60: YANAK YÜKSEKLİĞİ (LASTİĞİN TABAN GENİŞLİĞİNİN %’SEL ORANI)
- 18,5 Santimetrenin %60’i = 18,5 cm x 0,60 = 11,1 Santimetre
- Is the two-figure aspect ratio. This percentage compares the tire’s section height with the tire’s section width. For example, this aspect ratio of 60 means that the tire’s section height is 60% of the tire’s section width.

- R:
- R indicates the construction used within the tires casing. R stands for radial construction. B means belted bias and D stands for diagonal bias construction.

- 14: JANT ÇAPI (“İnç” ölçü birimi cinsinde 14 = 35,56 Santimetre)
- The last dimension listed in the size is the diameter of the wheel rim (jant çapı) , which is most often measured in inches.

**Bu Lastik ile, Aracın Yerden Yüksekliği:**- 57,76 cm = 22,2 cm (11,1 cm x 2) + 35,56 cm

- 185: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)
- 175/70R13 82T [2.1 Bar Hava Şişirim = 30,4579 PSI]
- 155/80R13 79T [ ? Bar Hava Şişirim = ? PSI]

**Aracı Satınaldığımda Üzerinde Var Olan Lastik:**

- 185/55 R15 82H
- 185: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)
- 185 Milimetre = 18,5 Santimetre = 0,185 Metre
- Identifies the tire section width, which is the measurement of the tire from sidewall to sidewall in millimeters. This measurement varies depending on the rim to which it is fitted.

- 55: YANAK YÜKSEKLİĞİ (LASTİĞİN TABAN GENİŞLİĞİNİN %’SEL ORANI)
- 19,5 Santimetrenin %55’i = 18,5 cm x 0,55 = 10,175 Santimetre
- Is the two-figure aspect ratio. This percentage compares the tire’s section height with the tire’s section width. For example, this aspect ratio of 55 means that the tire’s section height is 55% of the tire’s section width.

- R:
- R indicates the construction used within the tires casing. R stands for radial construction. B means belted bias and D stands for diagonal bias construction.

- 15: JANT ÇAPI (“İnç” ölçü birimi cinsinde 15 = 38,1 Santimetre)
- The last dimension listed in the size is the diameter of the wheel rim (jant çapı) , which is most often measured in inches.

**Bu Lastik ile, Aracın Yerden Yüksekliği:**- 58,45 cm = 20,35 cm (10,175 cm x 2) + 38,1 cm
- Bu lastik, orijinal 15 İnç janta uygun lastikle aynı ölçüde. Bu yüzden; yere aynı yükseklikte.

- 58,45 cm = 20,35 cm (10,175 cm x 2) + 38,1 cm

- 185: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)

**Aracın sahibinde, araca uyumlu ve yere biraz daha yakın lastik 4’lüsü vardı, o 4’lüyü aldım ve araca taktım. Modeli şöyle:**

- 195/50 R15 82H
- 195: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)
- 195 Milimetre = 19,5 Santimetre = 0,195 Metre

- 50: YANAK YÜKSEKLİĞİ (LASTİĞİN TABAN GENİŞLİĞİNİN %’SEL ORANI)
- 19,5 Santimetrenin %50’i = 19,5 cm x 0,50 = 9,75 Santimetre
- Is the two-figure aspect ratio. This percentage compares the tire’s section height with the tire’s section width. For example, this aspect ratio of 50 means that the tire’s section height is 50% of the tire’s section width.

- R:
- 15: JANT ÇAPI (“İnç” ölçü birimi cinsinde 15 = 38,1 Santimetre)
**Bu Lastik ile, Aracın Yerden Yüksekliği:**- 57,60 cm = 19,50 cm (9,75 cm x 2) + 38,1 cm
- Orijinalinden 8,5 mm (1 cm civarında) daha yere yakın

- 57,60 cm = 19,50 cm (9,75 cm x 2) + 38,1 cm

- 195: LASTİK TABAN GENİŞLİĞİ (“Milimetre” ölçü birimi cinsinde) (LASTİĞİN YERE BASAN TABAN KISMI)

**ÖNEMLİ KAYNAK İNTERNET SAYFALARI:**

- automobile-catalog.com
- goodyear.eu
- generaltire.com
- oponeo.ie
- pirelli.com
- polatlastik.com
- sizemywheels.com
- tyrecentredirect.com
- wheel-size.com

**Aracın Tam Model Bilgileri:**

- CHEVROLET KALOS 2005 .. 2008 1.4I (1.4 Litre)
- Generation: 2005 .. 2008
- Production: [2005 .. 2008]
- Sales regions: Europe
- Power: 93 hp | 69 kW | 94 PS
- Engine: I4 , Petrol
- Center Bore / Hub Bore: 56.6 mm
- Bolt Pattern (PCD): 4×100
- Wheel Fasteners: Lug nuts
- Thread Size: M12 x 1.5
- Wheel Tightening Torque: ?

**Bar vs. PSI:**